- - - - Joins up multiple indivIDual strings to form a single complete string. strcat.html Measure object High pin Low pin String1...10 Tolerance min Tolerance max Unit Ist notwendig einmalig vor K2000INI (am besten in den ersten 1000 Schritten) Hier wird ggf. der Firmware-Download veranlasst und die Anschaltung fr die K-Line auf die Ausg?ge der SKM. - Unit der SKM (z.B. CAN1 oder SKM_01) Timeout zwischen der SKM und dem Host in ms - - - Integrating DC voltage measurement with AUTO triggering. dcv.html MaxSignalAmplitude IntegrationPeriod STDPAV Makro for communication over CAN with ISO15765 protocol. (KWP2000 over CAN) can2000ini.html Measure object High pin Low pin Unit (i.e.:CAN1) Can driver (H/L) Baudrate in Baud (i.e.: 500000) Sample ratio in % (i.e.: 70) Terminater in Ohm (0/60/120) Kind of communication (1...4) Can send ID. (i.e.: 6F1) ID len in Bit (11/29) Can read ID. (i.e.: 7FE) ID len in Bit (11/29) Tolerance min Tolerance max Unit Indirect measurement of current by means of integrating DC voltage measurement with AUTO triggering on a defined measurement resistor. This function is always used when a current measurement resistor has to be inserted in a line to the unit (e.g. UB) for the duration of the measurement. Currents flowing into the unit register as positive. dcis.html Measure object High pin Low pin MaxSignalAmplitude IntegrationPeriod Shuntresistor Tolerance min Tolerance max Unit berechnen.html Measure object High pin Low pin Term Rounding_Method Tolerance min Tolerance max Unit Sends an interface protocol block from the tester via the serial interface to the unit. Depending on the mode a response (measured data block) may be expected from the unit; the response is written to a received data memory. That received data memory can be accessed by means of the functions BlockIntIDH_BlockInt and BlockStrIDH_BlockStr. comblock.html Measure object High pin Low pin Interface_Protocol_Block Bytes_Expected_Back Timeout Mode Tolerance min Tolerance max Unit This function can only be carried out after a read operation by the function ComBlockIDH_ComBlock. As its result it returns the bytes specified in the column Testing Parameters from low byte to high byte of a loaded measured data block and interprets them as integers. blockint.html Measure object High pin Low pin LowByte Tolerance min Tolerance max Unit Measurement of duration of a positive or negative pulse or a period. Depending on mode this function acts as a function or a measurement function. timea.html Measure object High pin Low pin MaxSignalAmplitude Tolerance min Tolerance max Unit Test read function for measurement of time duration of a pulse or a period. rtimea.html Measure object High pin Low pin Tolerance min Tolerance max Unit Test read function for measurement of time period between the trigger edges of two different test signals. The function RTimeAB may only be used in conjunction with the function TimeABIDH_TimeAB (mode s). rtimeab.html Measure object High pin Low pin Tolerance min Tolerance max Unit - Measure object High pin Low pin Tolerance min Tolerance max Unit Performs a bit operation on two integers. The result is also an integer. bitop.html Measure object High pin Low pin Tolerance min Tolerance max Unit - Measure object High pin Low pin Tolerance min Tolerance max Unit Internally or externally triggered integrating DC voltage measurement. Depending on mode this function acts as a function or a measurement function. dcvtrg.html Measure object High pin Low pin MaxSignalAmplitude Tolerance min Tolerance max Unit Test read function for internally or externally triggered integrating DC voltage measurement. rdcvtrg.html Measure object High pin Low pin Tolerance min Tolerance max Unit This function is used to implement program subroutines andloops in the PAV. The conditions supported are IF/THEN IF/THEN/ELSE and WHILE. A subroutine is terminated by ENDIF or ENDWHILE. The function must be invoked for every keyword. .html Measure object High pin Low pin Type Tolerance min Tolerance max Unit dcitrg.html Measure object High pin Low pin Shuntresistor MaxSignalAmplitude Tolerance min Tolerance max Unit Test read function for indirect current measurement function DCITrgIDH_DCITrg. The function RDCITrg may only be used in conjunction with the function DCITrgIDH_DCITrg (mode s). rdcitrg.html Measure object High pin Low pin Tolerance min Tolerance max Unit Indirect measurement of current by means of integrating DC voltage measurement with AUTO triggering on a defined shunt. This function is always used when a load with integrated shunt is connected to a unit pin and the current is to be measured on the integrated shunt. Currents flowing into the unit register as positive. dci.html Measure object High pin Low pin MaxSignalAmplitude IntegrationPeriod Shuntresistor Tolerance min Tolerance max Unit Terminates the test if a measured value is outsIDe the tolerance limits. This function does not return a value. break.html Measure object High pin Low pin Measured Value Tolerance min Tolerance max Unit - Measure object Measure object Measurement of frequency of a periodic signal. frequenz.html Measure object High pin Low pin MaxSignalAmplitude Tolerance min Tolerance max Unit This function is used to load a file that is in the ECU memory container in the form of a data block into the unit. The permissible data formats for the file in the container are binary (data is transferred 1:1 to the unit) VLB (Variable Length Binary; the file already contains segmented data) NOP format Intel-Hex and S19 format. The reference to the valID ECU memory container is embedded in the components list. loadfile1.html Measure object High pin Low pin Container_Type File_Name Tolerance min Tolerance max Unit Represents an integer value as a formatted string. printint.html Measure object High pin Low pin Value Characters Tolerance min Tolerance max Unit Creates an excerpt from a string. strcopy.html Measure object High pin Low pin String Tolerance min Tolerance max Unit - Measure object Converts a string into an integer value. strtoint.html Measure object High pin Low pin String Tolerance min Tolerance max Unit - Measure object - Measurement of effective level with automatic triggering. acv.html Measure object High pin Low pin MaxSignalAmplitude IntegrationPeriod Tolerance min Tolerance max Unit Measure object High pin Low pin MaxSignalAmplitude IntegrationPeriod Tolerance min Tolerance max Unit This function can only be carried out after a read operation by the function ComBlockIDH_ComBlock. It returns a string as its result. It does so by returning the bytes specified in the column Testing Parameters from the loaded measured data block as ASCII characters. blockstr.html Measure object High pin Low pin StartByte Tolerance min Tolerance max Unit Sends and/or receives messages via a CAN interface. This function may only be invoked once the interface has been initialized by means of the function CANInit. If the function reads a received message, that message is returned and at the same time written to a received messages memory (see also function ComBlock) which can be accessed using the standard functions canblock.html Measure object High pin Low pin ID_Send ID_Send_Length Tolerance min Tolerance max Unit Initializes the CAN interface. Following successful initialization, the testing station can communicate with the control unit using the function CANBlock. caninit.html Measure object High pin Low pin Interface ID Tolerance min Tolerance max Unit MaxSignalAmplitude IntegrationPeriod Measure object High pin Low pin MaxSignalAmplitude Tolerance min Tolerance max Unit Measure object n Tolerance min Tolerance max Unit n Tolerance min Tolerance max Unit Initializes and establishes communication via the diagnosis interface for the KW2000 protocol. In contrast with the function ComInitIDH_ComInit, which applies to all protocols (but does not permit any protocol-specific parameter settings), the function K2000Ini specifies all parameters that are required to establish communication. k2000ini.html Measure object High pin Low pin Target_Address Initialization_Type Specifies the type of initialization (stimulation) Default value: 2 Initialization_Line P2max W1max TiniL Tolerance min Tolerance max Unit This function is used to request general information on the testing station such as date of manufacture. The result returned is always a string. kundendat.html Measure object High pin Low pin Data_Type Tolerance min Tolerance max Unit legende.html Measure object High pin Low pin Description of Function Testing Points Tolerance min Tolerance max Unit This function is used to load a file that is in the ECU memory container in the form of a data block into the control unit. The permissible data formats for the file in the container are binary (data is transferred 1:1 to the control unit), VLB (Variable Length Binary; the file already contains segmented data), NOP format, Intel-Hex and S19 format. The reference to the valid ECU memory container is embedded in the components list. loadfile1.html Measure object High pin Low pin Container_Type File_Name Tolerance min Tolerance max Unit min max Unit min max Unit Represents a floating-point value as a formatted string. printfloat.html Measure object High pin Low pin Value Characters Tolerance min Tolerance max Unit Measurement of effective level with automatic triggering. The measurement must be prepared with the aid of the function ACVInit; RACV may only be invoked once the testing instrument has completed its settling period (AC voltage coupling). racv.html PAM position 1 Measure object High pin Low pin - - Tolerance min Tolerance max Unit PAM position 1 - - PAM position 1 - - Measure object High pin Low pin Tolerance min Tolerance max Unit This function is used to request a 'Key' for a 'Seed'. This can be necessary, for example, to be able to access control units with activated immobilizer or data that is normally locked via the diagnosis interface. seedkey.html PAM position 1 Measure object High pin Low pin - - Session_Name Seed_Method Seed Tolerance min Tolerance max Unit Measurement of time period between the trigger edges of two different test signals (on Channel A and Channel B). Depending on mode, this function acts as a control function or a measurement function. timeab.html Measure object High pin Low pin MaxSignalAmplitudeA Tolerance min Tolerance max Unit This function is used to perform the OBP handshake between the testing station and the control unit. It can not be executed until the handshake pin has been initialized by means of the function OBPInit1IDH_OBPInit1. If a malfunction occurs during the OBP handshake, the test is normally aborted. obphs.html Measure object High pin Low pin Tolerance min Tolerance max Unit Edge This function is used to perform the OBP handshake between the testing station and the control unit. It can not be executed until the handshake pin has been initialized by means of the function OBPInit1IDH_OBPInit1. If a malfunction occurs during the OBP handshake, the test is normally aborted. Measure object High pin Low pin Tolerance min Tolerance max Bool Success or Failure This function is used to perform the OBP handshake between the testing station and the control unit. It can not be executed until the handshake pin has been initialized by means of the function OBPInit1IDH_OBPInit1. If a malfunction occurs during the OBP handshake, the test is normally aborted. Measure object High pin Low pin Tolerance min Tolerance max Unit This function is used to perform the OBP handshake between the testing station and the control unit. It can not be executed until the handshake pin has been initialized by means of the function OBPInit1IDH_OBPInit1. If a malfunction occurs during the OBP handshake, the test is normally aborted. Measure object High pin Low pin Tolerance min Tolerance max Unit